Public Address (PA)

CATEGORIES

INPUT SOURCES

SIGNAL MANAGEMENT

POWER AMPLIFIER

CONTROL & MONITORING

LOUDSPEAKER

MH 1a, MH 2a, ME 1

ME 1: Unidirectional dynamic microphone with built-in push-to-talk switch.
MH 1 & MH 2: Unidirectional dynamic microphone with built-in slide switch with lock-plate.
600 Ω output impedance.
Cardioid characteristic helps reduce background noise and feedback.

MC 1, MC 2, & MP 1

Unidirectional dynamic microphone with built-in electronic chime unit.
User adjustable chime volume with OFF switch.
Unidirectional dynamic microphone.
A press-to-talk button to activate microphone and also to trigger the priority function of the system.

MC 3 & MP 2

Unidirectional gooseneck condenser microphone.
The number of selectable zones can be extended when atteched to the MX 102 Extension Unit with each unit having an additional control of 20 zones.
Phone Jack microphone socket output with screw terminal connector for trigger contact

MS 200 Series Remote Paging Console

Unidirectional condenser gooseneck microphone with a wide frequency response of 200 Hz to 18 kHz and features built in speech filter circuitry.
Self-deactivation if the active Remote Paging Console is left unattended for more than 1 minute.
Pre-announcement tune can be selected either at the MS 200 Series Remote Paging Console or at the CP 102 Remote Paging Console Communication Panel at the convenience of the user
The presentable priority mode (first In First Out (FIFO) or Remote Paging Console 1 as highest priority) can be set on the CP 102.

DS 201-S Digital Source Player

Multipurpose unit performing playback of CD quality Background Music (BGM) and pre-stored messages
SUtilizes SD Card and supports High Capacity (SDHC) SD Card for increased capacity for storage
User friendly front panel for message selection and playback
Unit able to be remotely triggered via the rear terminal block for message selection or BGM mode activation

MH 1a, MH 2a

ME 1: Unidirectional dynamic microphone with built-in push-to-talk switch.
MH 1 & MH 2: Unidirectional dynamic microphone with built-in slide switch with lock-plate.
600 Ω output impedance.
Cardioid characteristic helps reduce background noise and feedback.

MEDUSA 3 Integrated PA System

Built in 1200W (MED 312M) or 600W (MED 306M, MED 306S) power amplifier
Supports up to 8 MRM 06 remote microphone
Internal amplifier monitoring and standby amplifier changeover
Internal amplifier overload protection

MEDUSA 4 Integrated Signal Manager

12 zones speaker line selector (can be extended to 60 zones with LS 12A)
BGM broadcast with 4 paging priority levels (Remote Mic, LINE1, Fire Alarm, Firemen's Mode, Handheld Mic.)
Supports up to 8 MRM 06 remote microphone
Interface with MEI 60 for 12 zones (N-1, N, N+1) remote zone trigger (can be extended to 60 zones with LS 12A)

MA 2000 Series Mixer Amplifier

4 microphone inputs with user selectable phantom power
Individual gain control on all 4 microphone inputs
Short circuit and over current protection with resettable fuse cut-off. In the event of a short circuit, just rectify the line and reset the amplifier and normal operation will resume
Voice activated muting function enables MIC 1 to override all the inputs
Bass and Treble Master tone control for equalization and audio tuning
Dual mode power supple of either AC mains or DC battery supply

MEDUSA 5 - Public Address & Emergency Voice Alarm Control System

A Complete All-In-A Box Solution for your PA Needs
Compliance to international Fire Regulations
Network Ready with VECTUS
Ease of Installation & Cabling

XM SERIES Modular Mixer System

Each enclosure can accomodate up to modules. More than 1 enclosure can be linked together, should more than 10 modules be required for the system
No inter-module wiring required
8 user programmable functions for priority settings and external device interface
Runs off main of 240 Vac, 50 Hz via the built-in XM 92A power supply module, with provisions for 24 Vdc battery back up

eX 800 SERIES
eMatrix System

Supports a maximum of 20 audio inputs and 60 audio outputs (expandable to 188 speaker zones)
System configuring and automatic monitoring via Proprietary Graphic User Interface with remote monitoring over WAN or LAN network capabilities
Capable for interface with external systems ie; Building Management Systems or Fire Alarm Systems
Automatic event scheduling providing a fully-automated PA System requiring minimal human intervention

Programmable Amplifier

High quality and cost effective mixing amplifier
Multiple number of inputs; 3 groups consisting of 8 inputs total (6 inputs selectable between -2 dBV or -62 dBV and 2 auxiliary inputs)
3 line level outputs and 1 Rec. output provided to connect to power amplifier or external recorder
Bass and treble control

Mixer Amplifier

4 microphone inputs with user selectable phantom power
Individual gain control on all 4 microphone inputs
Short circuit and over current protection with resettable fuse cut-off. In the event of a short circuit, just rectify the line and reset the amplifier and normal operation will resume.
Voice activated muting function enables MIC 1 to override all the inputs.

Audio Power Amplifier

There are 8 models in the PB 1000 Series Audio Power Amplifier : PB 1406 (4 x 60W), PB 1412 (4 x 120W), PB 1024 (1 x 240W), PB 1224 (2 x 240W), PB 1048 (1 x 480W), PB 1060 (1 x 600W), PB 1260 (2 x 600W), PB 1120 (1 x 1200W).
Low THD+N (less than 1%)
Wide frequency response from 40Hz to 18 kHz
Convection cooled.

CA Series ABS Grille Ceiling Loudspeaker

120 mm dual cone full range loudspeaker component for a wide frequency response
Flush mounted on to the ceiling with the choice of either screw mounting or spring mounting for ease of installation and improved aesthetics
Wide coverage angle reduces the number of loudspeaker units required for evenly distributed sound coverage
Optional metal back enclosure available for installations that requires addtional protection to the loudspeaker unit

CE 560 Series ABS Grille Ceiling Loudspeaker

120 mm dual cone full range loudspeaker component for a wide frequency response
Flush mounted on to the ceiling with the choice of either screw mounting or spring mounting for ease of installation and improved aesthetics
Wide coverage angle reduces the number of loudspeaker units required for evenly distributed sound coverage
Optional metal back enclosure available for installations that requires addtional protection to the loudspeaker unit

Ceiling Loudspeaker

120 mm dual cone full range loudspeaker component for a wide frequency response
Flush mounted on to the ceiling with the choice of either screw mounting or spring mounting for ease of installation and improved aesthetics
Wide coverage angle reduces the number of loudspeaker units required for evenly distributed sound coverage
Metal back enclosure models available for installations that requires minimal crosstalk between adjacent zones

CM 361 Flush Mount Ceiling Loudspeaker

105 mm circular white epoxy coated metal grille, utilising a 75 mm dynamic full range speaker driver unit, suitable for generak PA applications requiring speech clarity.
Spring mounted installation to eliminate visible mounting screws.
Ready fitted line matching transformer with multiple impedance tappings, suitable for 70V and 100V line distributed loudspeaker system
Carefully designed with simplicity in installation & finished aesthetically for ease of matching to any ceiling type and interior facade.

CM 461 Flush Mount Ceiling Loudspeaker

105 mm circular white epoxy coated metal grille, utilising a 75 mm dynamic full range speaker driver unit, suitable for generak PA applications requiring speech clarity.
Spring mounted installation to eliminate visible mounting screws.
Ready fitted line matching transformer with multiple impedance tappings, suitable for 70V and 100V line distributed loudspeaker system
Carefully designed with simplicity in installation & finished aesthetically for ease of matching to any ceiling type and interior facade.

Splashproof Ceiling Loudspeaker

200 mm circular white epoxy coated metal grille and covered with a metal perforated mesh
Applications that calls for speech and music clarity.Dual cone full range speaker driver unit, suitable for general PA applications that calls for speech and music clarity
Spring mounted installation to eliminate visible mounting screws
Ready fitted line matching transformer with multiple impedance tappings, suitable for 70 V and 100 V distributed speaker system

Automatic Amplifier Changeover Unit

Monitors 8 duty amplifiers channels and 1 standby amplifier channel.
Performs 1 - to - 8 amplifier backup on first come first served basis
Automatic amplifier channel connection sensing.
General dry - contact upon amplifier failure for interfacing with external system.

Amplifier Monitoring Panel

Convenient monitoring of up to 10 power amplifier outputs
Large VU meter provided for accurate visual monitoring
75 mm dynamic full range loudspeaker unit with built-in attenuation for aural monitoring of the selected amplifier output
19" EIA standard rack moutable, taking only 2U rack space

Line Supervisory Unit

Built-in pilot tone signal generator
High precision line drivers enable accurate measurement of the loudspeaker line impedance up to a maximum distance of 1 km.
Impedance checking method allows for branching of loudspeaker lines without the need for end-line resistors and DC-blocking capacitors.
Allows for monitoring of loudspeaker line beyond the audio attenuator.

Speaker Line Selector

Removable screw type 100V line Input/Output connectors for ease of servicing
LED Status indicators provide easy visual monitoring
ALL CALL button for convenient triggering of all available 12 zones.
External remote control from MED 400P Integrated Signal Manager via RJ 45 connectors
1200W (100V line) maximum power handling per output
1U 19" EIA Standard rack mountable.

Audio Attenuator

Maximum insertion loss of -0.5 dB
Sleek and aethetically designed, constructed from high impact ABS with a white finish that blends easily into most surroundings
The flexibility of being flush mounted or surface mounted without any visible mounting screws
Built-in emergency overriding relay which sets the output level to maximum during emergency announcement

Power Supply Unit

Regulated 24 Vdc power supply up to a maximum of 6 amperes
Solid state protection against short circuit and overloading
Supports external backup power source of 24 Vdc which automatically switches over to load during main power failure
LED status indicators provide easy visual monitoring